Seamless Gutter System

A.M.G. GUTTERS & DOWNSPOUTS
STANDARD 5-K GUTTER INSTALLATION

A PROFESSIONALLY INSTALLED GUTTER SYSTEM FROM
A.M.G. GUTTERS & DOWNSPOUTS
CONSISTS OF THE HIGHEST QUALITY, MOST DURABLE
PRODUCTS AND COMPONENTS AVAILABLE TO COMPLETE
YOUR STANDARD INSTALLATION.

THIS WILL INCLUDE .027 ALUMINUM 5-K STYLE GUTTER,
WITH A BAKED ENAMEL FACTORY FINISH (
20 YEAR
MANUFACTURERS WARRANTY), MANUFACTURED AND
FABRICATED AT YOUR HOME OR BUSINESS.  2 x 3
DOWNSPOUT’S, ELBOWS AND ALL THE NECESSARY
COMPONENTS/PARTS INCLUDING BUT NOT LIMITED TO;  
END CAPS, HEAVY DUTY HIDDEN HANGERS, CONCEALED
OUTLETS, DOWNSPOUT STRAPS, CORNERS, AND THE
REPLACEMENT OF EXISTING METAL EXTENSIONS.  

ALL EXTERIOR FASTENERS WILL BE CORROSION-FREE
STAINLESS STEEL.  ALL INTERIOR FASTENERS WILL BE
RUST RESISTANT ZINC-PLATED AND/OR STAINLESS STEEL.

WE ALSO INSTALL
FASCIA BOARD, SHOULD THE NEED
ARISE THAT YOUR FASCIA BOARD IS NOT IN THE  
CONDITION SUITABLE FOR THE PROPER INSTALLATION
OF YOUR NEW GUTTER SYSTEM.

ALTHOUGH THE PHRASE SEAMLESS GUTTER IS
COMMONLY USED THROUGHOUT THE INDUSTRY, IT IS
IMPOSSIBLE TO AVOID SEAMS AT OUTLETS, CORNERS,
AND END CAPS.  THESE AREAS ARE SEALED WITH THE
HIGHEST QUALITY PERMANENT SEALER AVAILABLE ON
THE MARKET TODAY. (THIS PRODUCT CAN BE USED EVEN
UNDER WATER)  WE HAVE NOT SUFFERED ANY CALL
BACKS DUE TO LEAKS CAUSED BY THE FAILURE OF OUR
PERMANENT SEALER.

“AN INFORMED CUSTOMER IS OUR CUSTOMER”

Equipment and Components of the Industry

THIS IS AN EXAMPLE OF A PORTABLE GUTTER MACHINE. IF YOUR GUTTER CONTRACTOR DOES NOT HAVE ONE YOU CAN EXPECT DAMAGED GUTTER
AND A FLY BY NIGHT JOB. (GUTTER MACHINES COST LESS THAN $10,000.00 SO THERE’S NO EXCUSE NOT TO HAVE ONE.

THIS IS A ROLL OF .O27 ALUMINUM GUTTER COIL. WITH A BAKED ENAMEL PAINT FINISH .  YOUR GUTTERS
WILL BE MANUFACTURED ON
SITE TO YOUR CUSTOM LENGTHS, REDUCING NEEDLESS SEAMS , WASTE AND COST PASSING THE SAVINGS ON TO YOU.

THIS IS A VIEW OF THE K-STYLE PROFILE. 5-K AND 6-K STYLE GUTTER
PROFILES ARE AVAILABLE IN TWO THICKNESSES. 5-K IS PRODUCED PRIMARILY IN .027 BUT .032 CAN BE PURCHASED AT ADDITIONAL COST, WITH 6-K BEING PRODUCED IN .032

THIS IS AN EXAMPLE OF OUR
CONCEALED HANGER. THERE ARE MANY DIFFERENT STYLES/TYPES, THIS BEING ONE OF THE STRONGEST
ON THE MARKET, FULLY GUSSETED TO REDUCE SAGGING. WE PREFER TO USE OUR OWN SCREWS TO CONTROL THE QUALITY AND FINISH.

#10-1.5″ HEX HEAD ZINC PLATED INSTALLATION SCREW. THIS IS AN EXAMPLE OF THE TYPE OF SCREW THAT WE USE TO INSTALL  NEW GUTTER SYSTEMS. WE USE THIS TYPE OF SCREW FOR IT’S GRABBING POWER, STRENGTH AND RESISTANCE TO CORROSION.

#6 3/8″ STAINLESS STEEL SCREW. THIS IS AN EXAMPLE OF THE EXTERIOR FASTENERS WE USE TO ASSEMBLE GUTTER SYSTEMS. DUE TO THEIR  EXTREMELY HIGH RESISTANCE TO CORROSION THEIR RUST FREE APPEARANCE WILL LAST FOR YEARS. OTHER COMPANIES USELESS EXPENSIVE, POOR QUALITY ZINC SCREWS THAT ARE GUARANTEED TO RUST.

THIS AN EXAMPLE OF AN END CAP. END CAPS ARE USED TO END A RUN OF GUTTER. END CAPS ARE CRIMPED TO THE END OF THE GUTTER AND SEALED WITH A PERMANENT SEALER. FACTORY PAINTED TO MATCH YOUR NEW GUTTER SYSTEM.

HERE ARE EXAMPLES OF INSIDE AND OUTSIDE BOX MITER CORNERS. MATCHING PRE-PAINTED BOX MITERS ARE PREFERRED FOR THEIR APPEARANCE, STRENGTH AND EASILY REPAIRED MAKING THEM THE MOST POPULAR WAY OF FINISHING A CORNER.

HERE IS AN EXAMPLES OF AN OUTSIDE STRIP MITER CORNER. UNFORTUNATELY STRIP MITERS ARE ONLY AVAILABLE IN LIMITED COLORS SO THEY HAVE TO BE SPRAY PAINTED. SPRAY PAINT TYPICALLY DOES NOT MATCH THE FACTORY FINISH PROPERLY AND WILL NOT BE AS RESISTANT TO FADING AND PEELING. WE USE THEM MAINLY FOR BAYS OR WHEN REQUESTED TO MATCH AN EXISTING REPAIR.

HERE IS AN EXAMPLE OF A BAY HAND MITER. HAND MITERS ARE UNATTRACTIVE, USUALLY SPRAY PAINTED, WHICH IF IT MATCHES, FADES AT A DIFFERENT RATE THAN THE GUTTER VOIDING THE MANUFACTURERS PAINT WARRANTY.

A SEAMLESS GUTTER SYSTEM IS ONLY AS GOOD AS THE SEALANT USED TO SEAL IT. GEOCEL 2320 SELF-LEVELING,
HIGH-PERFORMANCE TRIPOLYMER SEALANT IS DESIGNED TO PREVENT
THE PASSAGE OR MOISTURE
THROUGH SMALL JOINTS AND
SEAMS FOUND IN GUTTER SYSTEMS.

THIS IS AN EXAMPLE OF OUR 2-3/8 ROUND DOWNSPOUT OUTLET USED TO ATTACH
THE DOWNSPOUT TO THE GUTTER. THIS APPLICATION CONCEALS THE FASTENERS
THAT HOLD THE OUTLET IN PLACE AND ELIMINATES TEARS IN THE GUTTER REDUCING THE CHANCE OF CLOGGED
AND DAMAGED DOWNSPOUT’S. ROUND OUTLETS ARE ALSO NATURALLY VENTED TO LET WATER DRAIN FASTER THAN TIGHT FITTING RECTANGULAR OUTLETS.

THIS IS AN EXAMPLE OF A 3″X 4″ RECTANGULAR COMMERCIAL DOWNSPOUT. A SPECIAL PUNCH IS REQUIRED TO INSTALL THESE OUTLETS. NOT MUCH NEED FOR VENTING AS THESE LARGE OUTLETS CAN HANDLE LARGE VOLUME OF WATER AND CAN BE USED ON RESIDENTIAL SYSTEMS WHEN MORE DRAINAGE IS REQUIRED.

THIS IS AN EXAMPLE OF OUR 2X3 DOWNSPOUT (STANDARD W/5-K STYLE INSTALLATION 3X4 COMMERCIAL DOWNSPOUT (STANDARD W/6-K STYLE INSTALLATION AND OPTIONAL FOR 5-K STYLE FOR TWICE THE WATER VOLUME)

THIS IS AN EXAMPLE OF A “B” ELBOWS WHICH IS FABRICATED FROM DOWNSPOUT MATERIAL AND IS AVAILABLE IN 2X3 AND 3X4, DESIGNED TO RUN THE DOWNSPOUT PARALLEL TO THE WALL.

THIS IS AN EXAMPLE OF AN “A” ELBOWS WHICH IS FABRICATED FROM DOWNSPOUT MATERIAL AND IS AVAILABLE IN 2X3 AND 3X4, DESIGNED TO RUN THE DOWNSPOUT PERPENDICULAR TO THE WALL.

THIS IS AN EXAMPLE OF A
STANDARD DIAMOND DOWNSPOUT STRAP USED TO ATTACH THE DOWNSPOUT TO THE BUILDING MADE FROM THIN .014 ALUMINUM.